Hardware and Material Explained

How to Prepare Nested DXF & DWG Files for CNC Cutting

DXF and DWG nesting example on a 1220 by 2440 mm sheet with red profiles, a white reference outline and at least 6 mm between part edges

A drawing can look tidy on screen and still leave the workshop guessing about its units, cutting side or quantities. This guide shows how to prepare a nested DXF or DWG for Armor Cases: build the layout at its real size, make the geometry unambiguous and use colour to distinguish cutting from reference information.

Use a 1220 × 2440 mm layout at 1:1 scale in millimetres, with at least 6 mm between neighbouring part edges. For service scope, material limits and arranging a job, see the CNC through-cutting product page. The sections below concentrate on preparing the drawing.

Start with a 1220 × 2440 mm reference rectangle

Draw the layout boundary in white and arrange the parts inside it. The white rectangle identifies the agreed sheet layout; it is reference information, not another machining profile. If the actual stock or proposed layout differs from 1220 × 2440 mm, have that difference checked before proceeding.

Use the finished dimensions of the parts. An edge intended to be 300 mm long should still measure 300 mm after export and reopening. Include a units note, check a known dimension and send the actual DXF or DWG you checked. A PDF can help explain the drawing, but it does not replace the requested CAD file.

If you use Autodesk Fusion, its official DXF export guidance is a useful starting point. The important handover check is that the exported geometry is interpreted in the intended units.

Keep at least 6 mm between neighbouring parts

Measure the gap between the finished edges of adjacent parts. A 6 mm cutter needs space to travel between them; the basic service therefore requires a minimum 6 mm separation. Do not let outlines touch, overlap or share a common cut line. This is different from measuring between the centres of two shapes.

Consider the layout as a whole. Grain direction or the chosen face can limit which parts may be rotated. Small pieces need appropriate support, and edge clearances may need review for workholding. Meeting the spacing rule is an important preparation step, rather than an automatic guarantee that every shape can be held and cut.

Make every through-cut and through-hole red

The outside profile follows the perimeter of the part you want to keep. Internal profiles identify openings to remove from it. Show both in red, including the circles or profiles for holes that go through the full material thickness. A white sheet outline remains reference-only.

CNC drawing colour key: white sheet reference, red through-cuts and holes, and blue depth machining excluded from the basic service
White is reference information; red is through-cutting. Shaded blue depth machining belongs to a separate assessment.

Remove duplicate lines, overlapping segments and construction geometry. Profiles intended to be closed should form continuous boundaries. Keep dimension text, notes and other reference information separate from the red cutting geometry, and explain any critical fit with a supporting view if necessary.

Understand why a square inside corner stays rounded

Our current setup uses a 6 mm diameter cutter, which has a 3 mm radius. It can travel around an outside edge, but cannot reach a perfectly square internal corner. Plan internal corners with at least a 3 mm radius and identify any fit that depends on the corner shape.

Inside and outside CNC profiles showing the rounded internal corner left by a circular cutter
A 6 mm cutter leaves an internal radius of at least 3 mm. Review tight-fitting joints before cutting.

For example, a square-edged tab can fail to seat in a slot whose internal corners are rounded. A revised radius or a reviewed relief feature, sometimes called a dogbone, can address that fit. Relief removes extra material and changes the appearance, so it should be discussed rather than added without considering the part.

Show finished-part geometry instead of guessing a tool-centre path. Leave cutter compensation to production unless a particular drawing convention is requested. Autodesk’s contour machining reference illustrates how manufacturing software distinguishes contours and applies compensation.

Keep shaded depth machining out of the basic service

Through-cutting goes all the way through the material. A pocket or rebate removes material only to a specified depth and belongs to a separate machining assessment. This basic product therefore accepts through-cut profiles and through-holes without shaded machining areas.

When discussing a separate depth-machining job, show the machined areas in light blue. If depths differ, use distinguishable shades and add a legend stating the depth in millimetres for every shade. Colour alone cannot communicate a machining depth. A flat drawing with stepped pockets is commonly described as 2.5D machining; the essential requirement is to specify which areas are cut and how deep.

Make the layout count match the sheet count

A drawing with five parts repeated on three sheets means three sheets of that layout, not five or fifteen sheets. Give each distinct layout an identifier and state how many sheets use it. If a different material, thickness or grain direction changes the layout, label that version separately.

Put the material and actual thickness in the accompanying brief so the drawing cannot become detached from its job information. Keep service eligibility and ordering questions with the current through-cutting service requirements.

Send a clear revision and confirm the handover

Use an identifiable filename such as enclosure-layout-rev-b-mm.dxf. Reopen it, check the reference size and a known part dimension, inspect the red profiles and confirm the part quantities. Identify any earlier revision it replaces and explain what changed.

Send the material, thickness, layout and sheet count together with your preferred completion date. Before cutting, confirm the accepted drawing revision, workholding, operations, price and timing. Sending a drawing or placing an order does not itself release a job to production.

To discuss your layout, contact Armor Cases in Auburn, or return to the basic CNC through-cutting service for the current scope.